VISIONGUARD8000VEHICLE SECURITY SYSTEMWITH BUILT-IN CAMERAAND REMOTE START PRODUCT MANUAL
Page 6 - VisionGaurd 8000Programable Functions using the LCD TransmitterPressing and holding transmitter button 4 will scroll through several transm
VisionGaurd 8000 - Page 7Camera Features
VisionGuard 8000 - Page 8
VISIONGAURD 8000 - Page 9Remote ArmingThe system monitors 5 independent areas (zones) while armed: doors, hood/ trunk, shock sensor, optionalsensor
Page 10- VisionGaurd 8000Tamper AlertIf the system was triggered while away, the LED will flash to indicate which zone triggered the system afterdisar
VisionGaurd 8000 - Page 11Panic ModeIn the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger thealarm.To
Page 12- VisionGaurd 8000To set the Emergency Override Code:1. Turn on ignition.2. Within 5 seconds, press the valet switch 5 times.· The siren will p
VisionGaurd 8000 - Page 13Remote StartingTo Remote Start the System:1. Be sure the system is not in Valet Mode.2. Press and hold Button 4 on one w
Page 14- VisionGaurd 8000Turbo Timer FeatureThe Turbo Timer feature allows vehicles with turbocharged engines to remain running after the ignition key
VisionGaurd 8000 - Page 15Extended FeaturesIgnition Door LockingFor added safety, the Ignition Door Locking feature allows vehicles equipped with
Limited Lifetime WarrantyThis vehicle security system is warranted to the original purchaser, to be free from defects inmaterial and workmanship. Th
Page 16 VisionGaurd 80001. Thoroughly read and become familiar with the installation instructions before beginning the installation.2. Review system
VisionGaurd 8000 - Page 17Mounting the Control UnitThe control unit must only be mounted in the interior of the vehicle. Do not mount the main unit
Page 18- VisionGaurdSystem Wiring6-Pin Starter HarnessPin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the
VisionGaurd 8000- Page 19when the door is open. This type of door circuit is usually found on Ford vehicles.Pin 12 GREEN WIRE: Negative Door Input (
Page-20 VisionGaurd 8000Jumper SelectionCarefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parkinglig
VisionGaurd 8000 - Page 21Entering System ProgrammingThis system is compatible with both the optional LCD transmitter or the standard FM transmitter
Page- 22 VisionGaurd5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors whenthe ignition is turned off. The
VisionGaurd 8000 - Page 238. Passive Door Locking. Selects whether or not the system will automatically lock the doors duringPassive Arming and Auto
Page-24 VisionGaurd 8000Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glowplugs are warm before cra
VisionGaurd 8000 - Page 25Wiring DiagramsTO POSITIVEDOME LIGHT+12VBlack/White(-) DOME LIGHTOUTPUTTO NEGATIVEDOME LIGHT+12VBlack/White(-) DOME LIGHTO
1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12. Remote Tra
Page-26 VisionGaurd 8000Negative TriggerPositive Trigger (using inverter or relays)Reverse Polarity VacuumAdding ActuatorsFollow the diagrams below fo
VisionGaurd 8000 - Page 27Two Stage Door Lock DiagramsTwo Stage Negative TriggerTwo Stage Positive TriggerThe VisionGuard 8000 is equipped with
Page-28 VisionGaurd 8000Two Stage Door Lock Diagrams cont’dTwo Stage Reverse PolarityTwo Stage Adding Actuators
VisionGaurd 8000 - Page 29FCC ID: OARRXAM2000This device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions:1) T
Page-30 VisionGaurd 8000Starter DiagnosticsStarter doesn’t start and parking lights flash:3 Times - Engine RPM not detectedHood Trigger is active4
VisionGaurd 8000 - Page 31
ScyTek Electronics11627 Cantara StreetNorth Hollywood, CA 91605© ScyTek Electronics 2006 VisionGuard 8000 r1 4/06Wiring DiagramScyNetBlue Start (-)Gr
The ScyTek Vision Guard 8000 is a combination vehicle security and remote starting system featuring abuilt-in "ScyNet Network Port" that all
Standard Remote Transmitter DescriptionThe VisionGuard 8000 is compatible with the optional 5-button Remote Transmitters used to control systemoperati
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desiredtransmitters r
Page 4 - VisionGuard 8000True Color 2-way Camera Ready Remote Transmitter DescriptionThe VisionGuard 8000 True Color 2-way LCD remote transmitter, is
VisionGuard 8000 - Page 55. The siren will chirp 3 times to indicate system has exited programming mode. System ConfirmationThe 2-way transmitter&ap
Kommentare zu diesen Handbüchern